Plumbing Basics: The First Step for Bathtub Installation
Plumbing Basics: The First Step for Bathtub Installation
Blog Article
How do you feel when it comes to How to Install a Bathtub?
Installing a bathtub isn't specifically rocket science, yet it does call for strong plumbing, woodworking, and in some cases, tiling abilities. Replacing an old bathtub with a new one is also a reasonably challenging job. If the old tub is readily accessible, the job can move speedily; if you have to open a wall to eliminate the old tub and position the new bathtub, the job is a lot harder. In either situation, the job is within a residence handyman's abilities, although you will require an assistant to vacate the old tub and also embeded in the brand-new one. See to it you have actually qualified yourself for the work and also are comfortable attempting it. Instead of hiring a service provider to take control of a halfway-completed project, it is better to consider utilizing one before you begin. Opportunities are you may need a professional plumber to make tube links.
This article will help you install a new bath tub in your restroom if you have already gotten a new bathtub and also don't require to transform the arrangement of your previous supply of water pipes.
Your devices and material checklist need to consist of the following:
Removing Old Touches
If you need to change old faucets with new ones as a part of your installment, then the first thing you should do is detach the supply of water. After doing so, turn on the taps to drain pipes any type of water continuing to be in the system. The process of getting rid of the existing taps can be rather bothersome due to the limited gain access to that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the taps. Have a towel prepared for the staying water that will originate from the pipelines. When the supply pipelines have been removed, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary faucets from transforming during this process. Once the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
Prior to proceeding to fit the brand-new taps, compare the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will need a plastic port to avoid damages to the string. One end of the connector fits on the plastic tail of the tap and the other end gives a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, place the tap in the installing hole in the bath/basin ensuring that the washing machines are in location in between the tap and the sink. Safeguard the faucet in position with the producer provided backnut. Once the tap is firmly in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet ports. The former kind should be connected to the tap ends first, tightening up only by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Setting up the Tub
Making use of both wood boards under its feet, put the bathtub in the called for setting. The wooden boards are useful in equally spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four little points.
The following objective is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the spirit level and adjusting the feet on the bathtub until the spirit level reads degree.
To set up taps, fit the bottom of the outermost flexible tap connector to the ideal supply pipeline by making a compression sign up with; after that do the very same for the various other tap.
Turn on the supply of water and also examine all joints and brand-new pipework for leaks as well as tighten them if required. Load the bath tub as well as likewise check the overflow outlet and also the regular electrical outlet for leakages.
Lastly, take care of the bath paneling as described in the manufacturer's instruction manual. Tiling and securing around the tub ought to wait till the bathtub has been made use of at the very least when as this will certainly resolve it into its final position.
Preparing for the Setup
First of all, the sustaining structure supplied with the bath ought to be fitted (if called for) according to the producer's guidelines. Next, fit the taps or mixer to the tub. When suitable the tap block, it is important to make certain that if the faucet comes with a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the taps unit to prevent pressure on the tub.
Fit the versatile faucet ports to the bottom of both faucets making use of 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you use all of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom should currently prepare to be fitted in its final setting.
Tiling Around the Tub
In the area where the bath meets the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to fracture a stiff seal, causing the water to penetrate the wall surface between the bathroom as well as the tiling, leading to difficulties with moisture and also possible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your components and also fittings. They are marketed in tubes and cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of drenched paper or soft rope. Keep in mind to constantly fill up the tub with water prior to securing, to enable the activity experienced when the bathtub remains in use. The sealant can break relatively very early if you do not consider this motion before sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also quickly offered on the market. It is a good idea to fit the floor tiles making use of waterproof or water-proof sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were made aware of that article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround through a friend on our other website. Enjoyed our blog entry? Please share it. Let another person find it. We love reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Book Today Report this page